3rd January 2022

  A new day deserves a new post


So my acetylene cylinder is empty.... no welding until the world wakes up for the new year in a week or so.


Well other stuff needs doing so had a look at a little ding in the back panel.
A solid object had impacted the rear bumper and bent it and created a little ding in the rear panel behind it. The same solid object may have also been responsible for destroying the original fuel tank.
Borrowed the serviceable one from my Series 1 Rapier which bolts right in.
This model has a larger tank than the earlier Minx models.

It was not a big issue so I just straightened the bumper and bolted it back on.

Pictures of dent in last post so here are some fresh ones:


Dent in rear after a little hammer and dolly work


Two low spots shown up by block sanding


A quick colour prime to see what still needs work





This is as far as you get with one spray can :-)


Nikko pen marks showing two spots needing further work

NOT the final colour, this is just a prime coat to sand back and see where I need any spot putty.



Comments

Post a Comment

Popular posts from this blog

Rust Repairs

Image
 It was all going so well, the "easy" task of straightening the pushed in face and making it like new. The few visible little rust holes to clean up and weld in some patches. In the last page I mentioned some classic Minx rust spots and posted a few pictures. However as with all rust what you see is just the very tip of the iceberg as a much larger amount is out of sight waiting to sink SS Titanic.  Now these rust spots do not start where you see them inside the engine bay where it is warm and dry and being a Hillman an oil film tends to cover surfaces. The problem started with the Rootes design that has a little dirt trap under the guards up out of sight where it can't be seen. Now if you hose out underneath on a regular basis and avoid roads where salt is added in winter there will not be a problem. So the hidden part collects "stuff" which holds moisture, and as we all know Fe + H20 = RUST. Eventually the little shelf rusts through and dirt and moisture enter...
Read more

So we sat and waited for two years for the OLD Bloke to get on with it, September 2024.

Image
Been tinkering again after a long period of distractions. Traveling, visiting, eating and all that time consuming stuff old folk seem to do. First task was to get the Californian running and back in the front shed. The overdrive had been causing issues and I decided to refit the original four speed to get it back on the road, with the help of a set of 3.89 gears I pulled out of a Hunter some time ago. Had always believed what I was told, that they would not work in the original Mk VIII housing. Seems I was misled and the Hypoid bevel centre section goes straight in, just changed the dif spider gears to match the coarse spline axles.  Clean out half the shed so I have plenty of room and popped 66M1NX in the middle up on stands Next step to refresh memory of where we  had got to. The rust trap under the front guard being the most obvious starting point Drivers side front guard Passenger side front floor Leaky rust holes in the rear screen opening. had been previously "fixed" wi...
Read more

Minx adjusts my priorities....again December 2021

Image
   The 66 series VI Minx has pushed to the front of the work priority list again. What can I say she is a pushy little Minx and is or was currently running and road legal Just went over the brakes with all new seals to master and slaves. Found a blocked hose to the rear brakes which may have explained the poor braking. Jim Withers to the rescue and new hose to complete the job. Some pictures of it as work progressed The self adjusting rear slave cylinders had been played with by a previous owner and were non functional so a little re-engineering to make them work as they should. The design of the little ratchet adjusters seems strange to be with parts that look like they should be assembled differently. Some creative work was also needed with the handbrake  as it had also been "improved" by a previous repair. I think I slipped in a new inner to the handbrake cable ten years ago when I first got the car which seems to be about 15mm too long to get the adjustments r...
Read more